Ecolink Z-Wave Motion Sensor PIR-ZWAVE2.5-ECOEcolink Z-Wave Alarm Listener FF-ZWAVE5-ECOEcolink Z-Wave Contact Sensor DW-ZWAVE2.5-ECOEcolink Z-Wave Siren SC-ZWAVE5-ECOEcolink Z-Wave Water Sensor FLF-ZWAVE5-ECOEcolink Zigbee 3.0 Contact Sensor DWZB1-ECOEcolink Zigbee 3.0 Water Sensor FLZB1-ECOEcolink Zigbee Alarm Listener FFZB1-ECOEcolink Zigbee Motion Sensor PIRZB1-ECO
Español 한국어

Ecolink Z-Wave Garage Sensor TILT-ZWAVE2.5-ECO

The TILT-ZWAVE2.5-ECO Z-Wave Plus Garage Door Tilt Sensor lets you know (remotely) if the garage door is opened or closed

↓

Features

Advanced Sensing

Monitors the open / closed status of garage doors and reports changes to your home management system.

Tamper Detection

Notifies your system when someone tampers with the sensor.

Wireless Operation

Battery powered Zigbee network operation enables installation flexibility.

Setup

Connected Home Setup

Setup Instructions

If you need to repeat the inclusion process, repeat STEP ONE above, then for STEP TWO you will need to simply remove the cover of the sensor, remove the battery for 5 seconds, reinsert the battery, and replace the sensor cover. This will re-start the sensor in inclusion mode.

Step 1:

Put your Z-wave Plus Controller into add (inclusion) mode.

Step 2:

The sensor enters add and remove (inclusion/exclusion) mode when powered on (when battery is added). Upon successful inclusion to a Z-Wave network, the sensor’s LED will turn solid RED for approximately 10 seconds abd then it will go out.

Step 3:

If the LED continues to flash, repeat the inclusion process (steps 1 & 2 above).

Step 1:

To identify location for sensor, it is very important that the Tilt sensor be located on the top section of a multi-panel garage door. This will be the first section to tilt when the door is opened and the last to move to the vertical position when closing.

Step 2:

To mount the sensor, before you mount the sensor, make certain that the arrow on the side of the Tilt sensor is pointing UP when assembled in the mounting bracket. The sensor can be mounted using adhesive tape and/or screws.

Step 3:

For mounting using adhesive tape, peel back the outer layer of one side of the adhesive tape, stick the tape to the garage door and press firmly. Peel back the outer layer on the other side of the tape and press the mounting bracket firmly onto the adhesive tape.

Step 4:

For mounting using screws, place the mounting bracket in the desired position on the garage door. Use the mounting bracket as a template to mark the location of the screw holes with a pencil. Drill a small hole through each of the marked locations. Use a screwdriver to fasten the mounting bracket to the door.

– Controller inclusion/exclusion mode must be activated BEFORE starting sensor inclusion or exclusion mode.
– The sensor can only be included into one controller network at a time, and must be excluded from one network before inclusion in another.
– The sensor automatically enters inclusion mode at power-up.
– Exclusion mode on the senor is initiated following the same exact procedure as inclusion.

Step 1:

Any device can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode.

Step 2:

Open the sensor’s case and remove the battery for 1 second. Replace the battery and the controller should remove the device from the Z-Wave network.

FAQ

Frequently Asked Questions

The sensor package includes:
1 x TILT-ZWAVE2.5-ECO Garage Door Sensor
1 x Sensor Mounting Bracket
2 x Mounting Screws for Sensor Bracket
1 x Sensor to bracket screw
1 x CR123A Lithim battery
1 x Adhesive tape

The sensor uses one (1) Lithium CR123A battery.

The sensor is a Z-Wave Plus compliant device and can participate in any standard Z-Wave network.

The sensor implements a radio-frequency (RF) communication protocol that allows the sensor to communicate with your system.

Yes. You can have multiple garage door sensors operating on the same network/system. Please consult with your system provider to determine if there is a limit on the total number of devices that can be associated with your system.

You can find self-help articles at the following site: https://discoverecolink.com/support/. Alternatively, you can request support via email by writing to [email protected]