Ecolink Z-Wave Motion Sensor PIR-ZWAVE2.5-ECOEcolink Z-Wave Alarm Listener FF-ZWAVE5-ECOEcolink Z-Wave Garage Sensor TILT-ZWAVE2.5-ECOEcolink Z-Wave Siren SC-ZWAVE5-ECOEcolink Z-Wave Water Sensor FLF-ZWAVE5-ECOEcolink Zigbee 3.0 Contact Sensor DWZB1-ECOEcolink Zigbee 3.0 Water Sensor FLZB1-ECOEcolink Zigbee Alarm Listener FFZB1-ECOEcolink Zigbee Motion Sensor PIRZB1-ECO
Español 한국어

Ecolink Z-Wave Contact Sensor DW-ZWAVE2.5-ECO

The DWZWAVE2.5-ECO is a battery-powered door/window sensor for home security or home automation applications

↓

Features

Advanced Sensing

Keeps track of the open/closed status of your doors/window and notifies you of any changes.

Tamper Detection

Notifies your system when someone tampers with the sensor.

Wireless Operation

Battery powered Zigbee network operation enables installation flexibility.

Setup

Connected Home Setup

Setup Instructions

• The sensor can only be included into one controller network at a time, and must be excluded from one network before inclusion in another.
• Removing the pull tab connects the battery and initiates sensor inclusion mode. Inclusion mode can also be initiated by removing the battery for at least 5 seconds, reinstalling the battery, then replacing the sensor cover.

Step 1:

Start by placing the controller into inclusion mode.

Step 2:

Activate inclusion mode for the sensor by removing the plastic pull-tab from the back of the sensor. When the inclusion process in complete, the LED on the sensor will be solid blue, then go out.

Step 3:

Test the sensor. Place the magnet next to the sensor to represent a closed position . If the LED flashes ONE TIME, it is successfully communicating on your Zwave network. If the LED on the sensor flashes slow and steady for 5 seconds, you need to repeat the inclusion process.

DW-ZWAVES2.5-ECO_MountingNote

The edge of the magnet must align with the line on the sensor, AND the magnet must locate next to the arrow on the sensor. Maximum gap between the magnet and the sensor is 5/8”. If the magnet is not located following these rules, the sensor may not get activated.

DW-ZWAVES2.5-ECO_MountingStep1
Step 1:

To identify Location for Sensor and Magnet, determine where on the door or window you are able to mount the sensor and magnet. Note, that the sensor has a line and arrow that identify where the magnet should be located, relative to the sensor.

DW-ZWAVES2.5-ECO_MountingStep2
Step 2:

For mounting the Sensor, make sure you have a flat clean surface to mount the sensor and magnet to. Verify the correct orientation of the sensor and location of the magnet before you continue on to mounting the sensor and magnet. Mount the sensor and magnet to a clean dry surface with the adhesive tape and/or the screws provided.

FAQ

Frequently Asked Questions

The sensor package includes:
1 x DWZWAVE2.5-ECO Sensor
1 x Magnet
2 x Mounting Screws
1 x CR123A battery
1 x Installation Manual
1 x 3M double sided tape

The sensor uses 1 CR123A battery.

The sensor is a Z-Wave compliant device and can participate in any standard Z-Wave network.

The sensor implements a check-in process by which it contacts the system on a periodic basis and provides an update of its operation state.

Yes. You can have multiple sensors operating on the same network/system. Please consult with your system provider to determine if there is a limit on the total number of devices that can be associated with your system.

You can find self-help articles at the following site: https://discoverecolink.com/support/. Alternatively, you can request support via email by writing to [email protected]